DIAGRA D RELEASE NOTES

All notable changes to DiagRA D will be documented in this file.

7.69.45.62573 Release (2025-10-10)

• Bugfix: Snapshot with A2L didn't run in some cases

• DoIP flash programming through D-PDU API is supported.

• Save OBD configurations for all protocols in the snapshot config file

• Bugfix: Snapshot output XML was not displayed

• Bugfix: XSD 2.0 and 3.0 schema files were missing "not available" for MIL status

• Implemented search highlighting for the selection of measurement values.

• Improve layout of the settings dialog to be more consistent with spacing and control widths.

• TCP communication:

• Improve behaviour when the web service TCP port is currently in use by another application.

• Bugfix in recording:

• Empty cells were accidently added in CSV and Excel recording.

• Values was not under the expected column headings when Infotype 0F is used in OBD Mode 9.

• RP1210: Properly read detailed version information from API and add it to the log file.

• Workaround for RP1210 filter limitation in Jaltest interface

• Function 'Send diagnostic services':

• Parameters for UDS service 0x28 CommunicationControl fixed

• Support of DoIP through D-PDU-API

• Results can be saved to a file

• List of standardized DTCs updated along SAE J2012. U07xx, U08xx and C08xx DTCs added.

• SAE J1979:

• All new PIDs and ITIDs for OBM Euro 7 added

• ITID 7B removed

• SAE J1939:

• Timeout for the reception of DM24 extended to 2 s

• Issue with PGN 0x8100 fixed (related to raw CAN interfaces)

• SPN 7352 and 7459 added

• SAE J1979-2:

• Improved presentation of test results

• Performance when showing freeze frames improved

• A message is displayed if no freeze frames are available

• Flickering of data fixed

• DIDs F51B-F51F added, DID F4AD fixed

• SAE J1979-3:

• Bugfix: Switching ECUs could cause data freeze in special cases

7.67.45.61458 Release (2025-06-23)

• Output of OBD Freeze-Frames in DTC snapshot for UDS VAG fixed
  
  

• Configuration of developer page OBD radar updated for Vitesco

• Webservices

• Bugfix: GetOBDFreezeFrameData provided incomplete data

• ClearECUFaultMemory shall not pass through any ResponsePending messages

• SAE J1979:

• Conversion of Infotype 81 fixed, which uses signed raw data

• SAE J1979-2:

• Bugfix: Duplicates in list of supported DIDs in output file fixed

• SAE J1939:

• SPN 2432 added to SAE J1939 config file

7.67.45.61338 Release (2025-06-02)

• Added SiL time synchronization with Vector FDX API

• Allow to erase each history list individually

• Activate automatic bitrate detection on CAN for interfaces with RP1210 D API

• Vector XL-API dll updated to version 24.40.30

• Conversion of PID $A3 for SAE J1699-3 fixed

• Improvements and bugfixes in Webservice API

• SAE J1939:

• Bugfix: Snapshot could freeze under certain conditions

• Workaround for communication issue in certain Hino trucks: SAE J1939 protocol significantly improved for raw CAN interfaces

• SPN 21226 added to config file

• Recording:

• Bugfix: In an MDF file with multiple ECUs in OBD mode 1, incorrect data could be written

• Bugfix: Each measurement value should have a unique timestamp in an MDF file

• DiagRA Script:

• Bugfix: DIAG::READ_VALUE_BY_NAME only ever returned first value if a group contained several values.

• Bugfix: Add missing command DIAG::USE_CAN_FD to activate or deactivate CAN FD (if supported by currently selected VCI channel).

7.66.45.60464 Release (2025-03-05)

• FlexRay | Extended Frame, Receive buffer extended to up to 8 kByte

• Updated trouble code files for VAG

• Code Clear for UDS VAG adapted to ECUs which support OBDonUDS

• PVD/SFD:

• Updating the service to use the latest HIL backend.

• Fix for communication issues in Windows 11.

• ASAP3: New UI element has been added in the Options page to keep a list of allowed IPs for ASAP3.

• Webservice: Improved documentation on flashing PDX/ODX files.

• Webservice: A new option has been added in setting page to choose port for Web Service.

• Fixed failing PDF conversion when the folder/file contained non-ASCII characters.

• Bugfix: Sporadic shifts/gaps in OBD with simultaneous recording.

• SAE J1979:

• Many Infotypes added to Mode 9. Configuration is now compliant to SAE J1979-DA from April 2024.

• SAE J1979-2:

• Added Chinese translation for SAE J1979-2 Data

• Support OBDonUDS response messages up to 8 kByte

• Bugfix: Snapshot files of SAE J1979-2 could save unexpected header of freeze frames under certain conditions

• SAE J1939:

• Several data stream SPNs added to config file

7.65.44.59732 Release (2024-12-09)

• Implemented a function on the developer pages that displays the results of the OBD radar statistics for Vitesco ECUs.

• The option "Load last configuration" now loads the last configuration and not just the last A2L/HEX/DBC files.

• Bugfix: Goepel CAN FD: Longer RX frames (> 184 Byte) may not be cached correctly.

• Fixed application log file name format.

• Application log file now uses UTF-8 encoding (with BOM).

• Replaced function call for setting bitrate in Kvaser interfaces to fix bitrate issues in some trucks

• Snapshots:

• TXT and XML files now contain an UTC timestamp that is formatted according to ISO 8601.

• Added a node for application name and version to the XML file.

• New version 3.0.0 of XML schema (XSD).

• Adjusted the XSL transformations to match the changes made to the *_OBD.xml files in in an earlier release.

• Bugfix: Missing comments added to the list of supported DIDs in the output files.

• J1699-3 test: Model years can now be selected up to 5 years ahead.

• List of standardized DTCs updated

• SAE J1979:

• Allow to record J1979 Mode 1/9 or 1/6/9 simultaneously

• SAE J1979-2:

• Bugfix: Data could have been assigned to the wrong ECU under certain conditions

• 'Rationality' page disabled as it is only used for SAE J1939

• Performance improvements when displaying a large number of DTC-based data

• SAE J1939:

• Several data stream SPNs added to config file

7.64.44.59120 Release (2024-10-10)

• Added an option to immediately create a HTML file with a snapshot

• Added an options page for the PDF page layout settings

• Highlight test results in the XML to HTML/PDF creation

• Fix display of ECU read and fault code read status the XML to HTML/PDF creation

• Bugfix: "Copy data to clipboard" for RX-Messages in send diagnostic services

• Bugfix: After the last Excel update, Excel crashed when writing comments

• Automatic bitrate detection for 250/500 kbps on ISO 15765

• SAE J1979:

• PID AD updated

• SAE J1979-2:

• Configuration file completely updated along SAE J1979-DA

• DIDs for China ZEV requirements added

7.63.44.58911 Bugfix Release (2024-09-19)

• Bugfix: Adjusted parser for S19/MOT flash files.

• Change: FlexRay Extended CAN ID request/Response changed to offset +0x2000

• SAE J1979:

• Bugfix: Sometimes display values data were duplicated

• Bugfix: XML output of binary data (PID 01, PID 03) could be duplicated under certain conditions

• SAE J1979-2:

• Data for Bank3/4 in DIDs F406-F409, F455-F458 temporarily deactivated to show data correctly in Freeze-Frame

• SAE J1939:

• Several data stream SPNs added to config file

• Missing SLOTs added to config file

7.63.44.58624 Release (2024-08-12)

• CAN output:

• Added support for sending OBD Mode 6

• Added support for sending complete OBD from Mode 1 to Mode A

• Bugfix in UDS. The error appeared only for a few values related to the battery.

• Added support for sending simultaneously Mode 1/6/9.

• Added configurable sleep interval in send diagnostic services

• Automatic baud rate detection for OBD protocols on CAN with Kvaser interfaces

• SAE J1979:

• Conversion of PID B5 fixed

• Conversion table for PID 1C updated

• SAE J1979-2:

• Conversion of DID F4B4 fixed

• Conversion table for DID F41C updated

• Use DID F501 to retrieve MIL-status if supported

• SAE J1939:

• Configuration file updated along SAE J1939-DA from June 2024

• Many data stream SPNs added to config file according to MY 2027 EPA

  
  

7.62.44.58318 Bugfix Release (2024-06-26)

• Bugfix: IXXAT/HMS interfaces didn't work in previous release

• Improved message for physical connection errors on the CAN bus

• SAE J1979:

• PID AC and PID D4 fixed for Mode 1/2

• Output of PID 7A fixed: User interface, recording, snapshot and CAN output

• Recording and snapshot for Mode 9 IUMPR data fixed for ECUs that report both Infotype 08 and 0B

• SAE J1979-2:

• Unit and Scaling IDs for test results updated according to latest SAE J1979-DA

• XML output for DTC based data improved

• Configuration file updated: Binary StatusOfDTC added, several unneeded data items removed

7.62.44.58090 Release (2024-05-28)

• Performance improvement when displaying fault memory and ECU identification

• Enable FlexRay for OBDonUDS protocol

• The serial number of the interface has been removed from the display name for communication channels 

• BREAKING: Web services that set the communication channel via the name may need to be adapted.

• Selection of OBD Scantool PIDs has been changed from a separate form to a list next to the displayed values

• List of DTCs updated along SAE J2012-DA from March 2024

• SAE J1979:

• PID AC and PID D4 fixed in Mode 1/2

• PID DB and DC added to Mode 1/2

• Infotypes 81-90, 96 and A3-A8 added to Mode 9

• SAE J1979-2:

• Many new DIDs added to config file

• Supported DIDs in the range of F4xx and F5xx are detected separately

• Bugfix: Freeze-Frames have not been requested correctly under certain conditions

• Implementation of DoIP in progress but not yet finished

• Failure Type Bytes updated along SAE J2012-DA from March 2024
  

• SAE J1939:

• Configuration file updated along SAE J1939-DA from February 2024

• Several data stream SPNs added to config file

• Several improvements in SAE J1939 CAN transport protocol to fix missing SPNs and freezing snapshot

• Table view in communication monitor fixed